NPM-TT2

NPM-TT2
Features

Basic Specification
Direct connectivity with NPM-D3/W2
Placement head (Lightweight 8- nozzle head & 3-nozzle head V2)
Selectable & configurable supply unit spec
Adoption of Multi Recognition Camera
Alternate & independent mounting support

Changeover capability
Multi Recognition Camera
High productivity through fully independent placement
Support Pin Automatic Change (option)

Productivity/Versatility
Feeder cart changeover spec(option)
Inspection option before pick-up
Transfer Unit(option)

Specfication
Model ID
NPM-TT2
PCB
dimensions
(mm)
PC size Single-lane mode L 50 x W 50 ~ L 510 x W 590
Dual-lane mode L 50 x W 50 ~ L 510 x W 300
M size Single-lane mode L 50 x W 50 ~ L 510 x W 510
Dual-lane mode L 50 x W 50 ~ L 510 x W 260
PCB exchange time
Single-lane mode 4.0 s (With no component mounted on the reverse side of PCB)
Dual-lane mode 0 s* *No 0s when cycle time is 4.0 s or less
Electric source 3-phase AC 200, 220, 380, 400, 420, 480 V 2.5 kVA
Pneumatic source Min.0.5 MPa, 200 L /min (A.N.R.)
Dimensions *1 (mm) W 1 300*2 x D 2 798*3 x H 1 444*4
Mass 2 690 kg
(Only for main body:This differs depending on the option configuration.)
Placement head Lightweight 8-nozzle head
(Per head)
3-nozzle head V2 *5
(Per head)
Placement speed PC size 18 000 cph (0.20 s/chip) 7 200 cph (0.50 s/chip)
5 900 cph (0.61 s/QFP)
M size 17 460 cph (0.21s/chip) 6 984 cph (0.52 s/chip)
5 723 cph (0.63 s/QFP)
Placement accuracy
(Cpk1)
± 40 µm/chip
± 30 µm/QFP 12mm to 32mm
± 50 µm/QFP 12mm Under
±40 μm/ chip
±30 μm/ QFP
Component
dimensions
(mm)
0402 chip*6 to L 32 x W 32 x T 12 0603 chip to L 150 x W 25 (diagonal152) x T 30
Component
supply
Taping Tape : 4 to 56 / 72 mm Tape : 4 to 56 / 72 / 88 / 104 mm
Specifications for front/rear tray feeders : Max.52
Specifications for front/rear feeder carts : Max.120 (Tape:4, 8 mm)
Stick Specifications for front/rear tray feeders : Max.12 (Single stick feeder)
Specifications for front/rear feeder carts : Max.28 (Single stick feeder)
Tray Max.40 (Front supply unit : Max. 20 + Rear supply unit : Max. 20)
*1 : Only for main body
*2 : 1 820 mm in width if extension conveyors (260 mm) are placed on both sides
*3 : Dimensions shown are specifications for front/rear tray feeders . Dimensions of specifications for front/rear feeder carts : 2 893 mm
*4 : Excluding the monitor, signal tower and ceiling fan cover.
*5 : 3-nozzle head V2 cannot be installed on NPM-D3
*6 : The 0402 chip requires a specific nozzle/feeder.
*Placement tact time, inspection time and accuracy values may differ slightly depending on conditions.
*Please refer to the specification booklet for details.

NPM-TT2